Metallic Paint Material Safety Data Sheet

SECTION 1 - GENERAL INFORMATION

MANUFACTURER                             HMIS RATING

Perfetto Finishes, Inc.                                           Health 1

202 5th St N

Wheaton, MN 56296, USA                                  Flammability 0

                                                                            Reactivity 0

Emergency Telephone (402) 563-1426

Product Name: Metallic Paint

Date of Preparation: May 5, 2007

SECTION 2 - HAZARDOUS INGREDIENTS

Hazardous Component:                 CAS OSHA PEL ACDIH TLV  None Present

Contains a proprietary water-based acrylic latex emulsion.

SECTION 3 - HAZARDOUS IDENTIFICATION

Emergency Overview: This material is a clear water-based topcoat. It is stable, non-flammable, translucent.

Primary Routes of Exposure:      Inhalation  - Skin Contact  -Eye contact

Potential Acute Health Effects:  

              Inhalation:   May cause respiratory tract irritation

              Skin:          Prolonged or repeated skin contact may cause irritation

              Eye:           May cause eye irritation

              Ingestion:    Not hazardous under intended use conditions.

Potential Chronic Health Effects:   None Known.

SECTION 4 - FIRST AID MEASURES

Eye Contact:        Flush eyes with clean water for 15 minutes. Seek medical attention

Skin Contact:       Thoroughly wash with soap and water before coating dries

Inhalation:           If irritation occurs, remove to fresh air and seek medical attention if a cough or

                            other symptoms develop. If affected, remove from exposure.

Ingestion:            Do not induce vomiting. Seek Medical attention immediately.

Section 5 - Fire Fighting Measures.

Flash Point:                                None

Flammability Classification:       Not Applicable

Extinguishing Media:                 Use water spray, foam, or carbon dioxide when fighting fires.

Protection to Firefighters:          As in any fire, wear NIOSH approved self-contained breathing

                                                   apparatus pressure-demand and full protective gear.

Fire and Explosion Hazards:      Material will not burn.

SECTION 6 - ACCIDENTAL RELEASE MEASURES

Personal Precautions:    Slippery: can cause slips and falls if walked on while wet.

Clean Up methods:        Contain spill with sand or other diking material. Soak up small spills

                                      with absorbent material. Dispose of in accordance with federal, state,

                                      and local regulations.

SECTION 7 - HANDLING AND STORAGE

Handling:       DOL storage category: not applicable.

Storage:         Keep from freezing. Keep container closed when not in use. Store in only

                      approved labeled containers. Do not take internally. Keep away from children.

                      Avoid extreme heat.

SECTION 8 - EXPOSURE CONTROLS/PERSONAL PROTECTION

ENGINEERED CONTROLS                IF NECESSARY, USE GENERAL ROOM DILUTION VENTILATION, PROCESS ENCLOSURES,

                                                LOCAL EXHAUST VENTILATION OR OTHER ENGINEERING CONTROLS TO CONTROL AIRBORNE

                                                LEVELS BELOW RECOMMENDED EXPOSURE LIMITS. USE ADEQUATE VENTILATION.

                                                AVOID BREATHING VAPOR AND SPRAY MIST.

EYE PROTECTION:                        EYE CONTACT SHOULD BE AVOIDED. WHERE EYE CONTACT IS LIKELY, WEAR

                                                chemical splash goggles and/or full-face shield.

Skin Protection:                       Wear gloves to prevent prolonged skin contact

Respiratory Protection:            None needed under normally anticipated use conditions. If vapor levels

                                                exceed allowable limits, wear a NIOSH approved air-purifying respirator

                                                with an organic vapor cartridge.

General Hygiene Practices:     Avoid eye skin contact. Avoid breathing vapors. Wash hands

                                                thoroughly with soap and water before eating or drinking.

SECTION 9 - PHYSICAL DATA

Appearance:                 Translucent white flowable liquid

Odor:                             Very mild latex smell

Boiling Point:                Above 200 degree F

pH:                                8.5 to 9.0

Vapor Pressure:            N/D

Melting point:                N/A

Odor Threshold:            N/D

Vapor Density:               Heavier than air

Solubility in Water:        Dilutable in Water

SECTION 10 - STABILITY AND REACTIVITY

Stability:                                               stable, non-reactive

Hazardous Polymerization:                  will not occur

Incompatibility:                                     None Known

Hazardous Decomposition Products:    by fire, carbon dioxide, and carbon monoxide

SECTION 11 - TOXICOLOGICAL INFORMATION

Carcinogenicity: This material is not considered a carcinogen by IARCor NTP and is not regulated as a carcinogen by

OSHA

SECTION 12 - ECOLOGICAL INFORMATION

Chemical Fate and Effects:     No data available

SECTION 13 - DISPOSAL CONSIDERATIONS

 

Waste from this product is not hazardous as defined under the Resource Conservation and Recovery Act (RCRA) 40 CFR 261. Incinerate in approved facility. Do not incinerate closed container. Dispose of in accordance with Federal, State/Provincial and local regulation regarding pollution.

SECTION 14 - TRANSPORTATION INFORMATION

DOT proper shipping description:    Paint and Related Materials, NOIBN

IATA/IMDG shipping description:     Paint and Related Materials, NOIBN

SECTION 15 - REGULATORY INFORMATION

SARA 313:   Product does not contain components at such a level as to require reporting under this statute.

All chemicals in this product are listed or are exempt from listing on the TSCA Inventory.

SECTION 16 - OTHER INFORMATION

Disclaimer:

Perfetto Finishes believes, to the best of its knowledge, and information that the information contained herein to be accurate and reliable as of the date of this MSDS sheet. However, because the conditions of handling, use, and storage of these materials are beyond the control of Perfetto Finishes, we assume no responsibility or liability for personal injury or property damage incurred by the use of these materials and make no warranty, expressed or implied, regarding the accuracy or reliability of the data or results obtained from their use. All materials may present unknown hazards and should be used with caution. The information and recommendation in this MSDS sheet are offered for the user's consideration and examination. It is the responsibility of the user to determine the final suitability of this information and data and to comply with all applicable international, federal, state and local laws and regulations.